How to add secondary IP to KVM VPS CentOS 6.9 Kloxo?

[SanOS]

Hi.
At first i thanks for great kloxo control panel.
Please help for solving problem.
When i was installing centos only one IP added to centos.
afterward i installed Kloxo mr 7.

I added secondry IP by kloxo but it did not worked.
Then I remove it and added by system-config-network but it did not worked.
Then i edit ifcfg-eth0:0 but it did not worked.

created ifcfg-eth0:0 by kloxo:

Code: [Select]

DEVICE=eth0:0
ONBOOT=yes
BOOTPROTO=static
IPADDR=167.114.x.y
NETMASK=255.255.255.255
NETWORK=167.114.x.y
GATEWAY=

Other ifcfg-eth0:0

Code: [Select]

DEVICE=eth0:0
BOOTPROTO=static
TYPE=Ethernet
IPADDR=167.114.x.y
NETMASK=255.255.255.255
GATEWAY=167.114.g.254
NM_CONTROLLED=no
USERCTL=yes
PEERDNS=yes

ifconfig show

Code: [Select]

eth0      Link encap:Ethernet  HWaddr 02:00:00:00:00:10
          inet addr:167.114.x.z  Bcast:167.114.x.z  Mask:255.255.255.255
          inet6 addr: fe80::ff:fee5:8a66/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:4636930 errors:0 dropped:0 overruns:0 frame:0
          TX packets:40573 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:467983224 (446.3 MiB)  TX bytes:5551887 (5.2 MiB)

eth0:0    Link encap:Ethernet  HWaddr 02:00:00:00:00:10
          inet addr:167.114.x.y  Bcast:167.114.x.y  Mask:255.255.255.255
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:4839 errors:0 dropped:0 overruns:0 frame:0
          TX packets:4839 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:299642 (292.6 KiB)  TX bytes:299642 (292.6 KiB)


Ping in vps

Code: [Select]

[root@localhost ~]# ping 167.114.x.y -c 5
PING 167.114.x.y (167.114.x.y) 56(84) bytes of data.
64 bytes from 167.114.x.y: icmp_seq=1 ttl=64 time=0.041 ms
64 bytes from 167.114.x.y: icmp_seq=2 ttl=64 time=0.033 ms
64 bytes from 167.114.x.y: icmp_seq=3 ttl=64 time=0.035 ms
64 bytes from 167.114.x.y: icmp_seq=4 ttl=64 time=0.044 ms
64 bytes from 167.114.x.y: icmp_seq=5 ttl=64 time=0.042 ms

--- 167.114.x.y ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 4000ms
rtt min/avg/max/mdev = 0.033/0.039/0.044/0.004 ms

Ping at dnsstuff.com
http://www.dnsstuff.com/tools#ping|type=ipv4&&value=167.114.x.y

Code: [Select]

TTL 56
Is TTL Default? Yes
Timeout Value 1
Is Timeout Default? Yes
Ping 1: Failed to receive reply: Timed out waiting for reply
Ping 2: Failed to receive reply: Timed out waiting for reply
Ping 3: Failed to receive reply: Timed out waiting for reply
Ping 4: Failed to receive reply: Timed out waiting for reply
Summary 4 packets lost [100%]


[SanOS]

I add 2nd ip by kloxo and then click on Re Read IPaddress .

I see in kloxo

Code: [Select]

BOOTPROTO=htcp
but in ifcfg-eth0:0 file is

Code: [Select]

BOOTPROTO=static
Maybe kloxo has a bug?

[SanOS]

Main IP PING is good
http://www.dnsstuff.com/tools#ping|type=ipv4&&value=167.114.x.z

Code: [Select]

TTL 56
Is TTL Default? Yes
Timeout Value 1
Is Timeout Default? Yes
Ping 1: 64 bytes from (167.114.219.54): icmp_seq=1 ttl=46 time= 65.60 ms
Ping 2: 64 bytes from (167.114.219.54): icmp_seq=2 ttl=46 time= 65.48 ms
Ping 3: 64 bytes from (167.114.219.54): icmp_seq=3 ttl=46 time= 65.61 ms
Ping 4: 64 bytes from (167.114.219.54): icmp_seq=4 ttl=46 time= 65.32 ms
Summary 0 packets lost [ 0%]
Minimum ping time: 65.32 ms
Average ping time: 65.50 ms
Maximum ping time: 65.61 ms
Standard deviation: 0.121 mshttp://167.114.x.z

[MRatWork]

Kloxo-MR think secondary IP as dhcp because main IP is dhcp type IP.

If you think secondary IP is static file (ask to provider to make sure) and then modified their ifcfg-eth0* file and click 're-read' after that in panel.

[SanOS]

Thanks
My problem was that 2nd IP had not ping in internet and could not show kloxo.
Solved.
Because Provider of VPS forget set mac address of that!
Thanks